In addition, we’ll provide some tips and tricks to make the process as easy as possible. This does not cover forgotten combinations.Are you looking for a way to drill holes in your project for cam lock connectors easily? This blog post will show you how to drill holes for cam lock connectors. See here to send in Q: What is the warranty on the Combi-Cam?Ī: The Combi-Cam Drawer Lock has a one year warranty against manufacturing defects. There are no special opening codes for the combination. If the lock is installed and the door/drawer is closed, you will need a locksmith (just as you would if you lost the key) and if it is not installed, you are better off buying a new one to replace it. Q: What can I do if I forget my combination? You may be able to push the reset button in but it will not change the combination. Before you can reset the combination, the number must be on the correct combination for the cam before resetting it. You did not start with the correct number that unlocks the cam. You did not leave the reset button pushed in.Ģ. It is that easy! Q: I push in the reset button but it does not change the combinationġ. After you have changed the numbers to your desired combination, let go of the button.Ĥ. Use a paper clip to turn the push the reset button in and leave it pushed in while resetting the numbers.ģ. Have the combination set on the one that opens the camĢ. The Combi-Cam combination is very easy to change and requires no special tools.ġ. Combi-Cam Drawer Lock had you, the consumer, in mind when we designed the recombination feature. Q: What material thickness do these locks accommodate?ħ850XL -with the 1-3/8" cylinder = material thickness up to 1-1/8"ħ850L with the 1-1/8" cylinder = material thickness up to 7/8"ħ850M with the 7/8" cylinder = material thickness up to 5/8"ħ850S with the 5/8" cylinder = material thickness up to 3/8" Q: How do I change the combination?Ī. Now when the cam rotates 90 degrees, the reset button is no longer accessible. Replace the Screw & Washer, the Cam, and the Stop Cam.ĥ. With the reset button in view, rotate the cylinder 180 degrees.Ĥ. Remove the Screw & Washer, the Cam, and the Stop Cam.ģ. Go ahead and set the desired combination to the Combi-Cam Drawer Lock.Ģ. To make the Combi-Cam less likely to be changed (hiding the reset button), follow the below instructions:ġ. In some cases installers of the Combi-Cam may not want the users to be able to easily change their own combination. The answer to this is almost opposite of the prior question. Click here Q: What if I don't want Combi-Cam users to be able to change the combination?Ī. Test each dial up one and down one for 6 possible combinations. Instead of 1-2-3 you end up with a combination of 223. If that does not work, click hereĪ2- As you set the dials you accidentally roll one up to the left that you already set. Less common is the in the middle of rolling up one dial. Example- setting code to 1-5-4 and you let go of button after the first dial and you roll the second dial at all prior to pushing the button again. Everything afterwards will be 0 when you release the button. See the two most common mistakes that happen and how to resolve.Ī1- When setting the combination you briefly let up on the button while rolling the dials. Q: I set my combination and am now locked out.Ī. rotate the cylinder 180 degrees until you see the reset button and then reassemble. Remove the screw, lock washer, cam and stop cam. During installation or when taking it apart drawer lock, you rotated the inside cylinder. Q: Why can I not see the reset button to recombinate my lock?Ī. Instead, grab the flat sides of the threaded cylinder between finger and thumb. Since these two turn together when unlocked, of course the lock will not turn when holding on to both. A common mistake when people go to test the lock is that they grab the combination head with one hand and the cam (arm in back) with the other. The lock will always come from the factory at all zeros. Frequently Asked Questions- Drawer Lock Q: I just bought my Combi-Cam and the lock will not turn at all zeros.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |